US-200C Standing Seam Panel
When aesthetic requirements call for a curved roof, the Ultra Seam US-200C Curved Panel is the system of choice. The mechanically seamed panels can be curved to a 19” inch radius.
Thursday, April 19, 2007
Metal Roofing Profile US-150bp
US-150BP Bermuda Panel System
When aesthetic requirements call for a horizontal appearance, the Ultra Seam US-150BP Bermuda Panel is the system of choice. Panels are available in galvanized, galvalume, aluminum and copper
When aesthetic requirements call for a horizontal appearance, the Ultra Seam US-150BP Bermuda Panel is the system of choice. Panels are available in galvanized, galvalume, aluminum and copper
Metal Roofing Profiles US-100fp
Ultra Seam Flush Panel and Wall Soffit System
The Ultra Seam Flush Panel system is ideal for gable walls and soffits where a smooth flat surface is desired. Horizontal flanges of 1-1/8" or 1-1/2” seams interlock and provide attachment surfaces for concealed fasteners. The panel seam combined with attachment flanges strengthens the panel to provide good spanning capacity. Fewer supporting structural members needed for high gables and wider soffits means lower installation cost. Available in twelve inch and sixteen inch widths.
The Ultra Seam Flush Panel system is ideal for gable walls and soffits where a smooth flat surface is desired. Horizontal flanges of 1-1/8" or 1-1/2” seams interlock and provide attachment surfaces for concealed fasteners. The panel seam combined with attachment flanges strengthens the panel to provide good spanning capacity. Fewer supporting structural members needed for high gables and wider soffits means lower installation cost. Available in twelve inch and sixteen inch widths.
Metal Roofing Profile US-100cs
US-100CS Standing Seam Panel
Cap Seam panel has a single upstanding leg on each side. After a panel is laid, the clips are installed up against the panel leg, with half of each clip folded over the leg. The adjacent panel is then laid up against the clips, and the other half of each clip is folded down. Finally the batten cap is snapped down over all clips in the seam along the entire length of the panel. The panels are now securely attached with the completed seam enclosing all clips. Seams require no machine closing and rapid installation means low in-place cost. Also available in 1-1/2" rib height (US-150CS). Cap Seam panel can also be curved or tapered. These panels create an architecturally desirable look without jeopardizing the integrity of the roof panel. The installation of the curved cap seam panel (US-100 CCS) and the tapered cap seam panel (US-100 TCS) is the same as the straight cap seam panel (US-100 CS).
US-200SB Snap Batten System
Cap Seam panel has a single upstanding leg on each side. After a panel is laid, the clips are installed up against the panel leg, with half of each clip folded over the leg. The adjacent panel is then laid up against the clips, and the other half of each clip is folded down. Finally the batten cap is snapped down over all clips in the seam along the entire length of the panel. The panels are now securely attached with the completed seam enclosing all clips. Seams require no machine closing and rapid installation means low in-place cost. Also available in 1-1/2" rib height (US-150CS). Cap Seam panel can also be curved or tapered. These panels create an architecturally desirable look without jeopardizing the integrity of the roof panel. The installation of the curved cap seam panel (US-100 CCS) and the tapered cap seam panel (US-100 TCS) is the same as the straight cap seam panel (US-100 CS).
US-200SB Snap Batten System
Metal Roofing Profile US 150c
US-150C Standing Seam Panel
When aesthetic requirements call for a curved roof, the Ultra Seam US-150C Curved Panel is the system of choice. The mechanically seamed panels can be curved to a 19” inch radius.
When aesthetic requirements call for a curved roof, the Ultra Seam US-150C Curved Panel is the system of choice. The mechanically seamed panels can be curved to a 19” inch radius.
Metal Roofing Profile US-150
US-150 Standing Seam Panel
The Ultra Seam standing seam system utilizes state of the art technology for roof integrity and positive weather-tightness. The Ultra Seam US-150 panel has been extensively tested in both steel and aluminum, and meets the stringent requirements of the “Standard Test Method for Structural Performance of SSMRS by Uniform Static Air Pressure Difference,” which has been adopted as ASTM E-1592. Seams require machine closing, by either hand or power seamers, both available on a job rental basis. The seaming process completely encloses and seals all clips and fasteners for the most watertight seal available. The US-150 panel, in addition to the standard 90-degree seam, can be double-locked to obtain a 180 degree architectural profile. The standing seam system is especially suitable where roof slopes are long and/or low, and unusually long panels are required. Available in various gauges of galvanized steel, galvalume, zincalume, aluminum, copper, zinc and stainless steel. Regardless of which material is selected, the optional stiffening ribs or striations are highly recommended in order to reduce the slight surface waviness of the metal known as “oil-canning.” Note: “oil-canning” is a natural phenomenon inherent in sheet metal products and therefore is not cause for rejection of the material.
The Ultra Seam standing seam system utilizes state of the art technology for roof integrity and positive weather-tightness. The Ultra Seam US-150 panel has been extensively tested in both steel and aluminum, and meets the stringent requirements of the “Standard Test Method for Structural Performance of SSMRS by Uniform Static Air Pressure Difference,” which has been adopted as ASTM E-1592. Seams require machine closing, by either hand or power seamers, both available on a job rental basis. The seaming process completely encloses and seals all clips and fasteners for the most watertight seal available. The US-150 panel, in addition to the standard 90-degree seam, can be double-locked to obtain a 180 degree architectural profile. The standing seam system is especially suitable where roof slopes are long and/or low, and unusually long panels are required. Available in various gauges of galvanized steel, galvalume, zincalume, aluminum, copper, zinc and stainless steel. Regardless of which material is selected, the optional stiffening ribs or striations are highly recommended in order to reduce the slight surface waviness of the metal known as “oil-canning.” Note: “oil-canning” is a natural phenomenon inherent in sheet metal products and therefore is not cause for rejection of the material.
Metal Roofing Profile US-175L
US-175LS Lock Seam Panel
Ribs of adjacent Lok Seam panels snap together, enclosing the concealed clips and provide a positive metal-to-metal lock. In turn, the enclosed clips positively secure the adjacent panels to the roof structure. Seams require no machine closing, yet are continuously and securely locked in place. By eliminating the need for mechanical seaming, installation time and cost can be greatly reduced. Also available in 1-1/2" rib height (US-150LS). The US-150LS has a slightly different locking detail from the US-175.
Ribs of adjacent Lok Seam panels snap together, enclosing the concealed clips and provide a positive metal-to-metal lock. In turn, the enclosed clips positively secure the adjacent panels to the roof structure. Seams require no machine closing, yet are continuously and securely locked in place. By eliminating the need for mechanical seaming, installation time and cost can be greatly reduced. Also available in 1-1/2" rib height (US-150LS). The US-150LS has a slightly different locking detail from the US-175.
Metal Roofing Profiles US-200
Profiles
US-200 Standing Seam Panel
The Ultra Seam standing seam system utilizes state of the art technology for roof integrity and positive weather-tightness. The Ultra Seam US-200 panel has been extensively tested in both steel and aluminum, and meets the stringent requirements of the “Standard Test Method for Structural Performance of SSMRS by Uniform Static Air Pressure Difference,” which has been adopted as ASTM E-1592. Seams require machine closing, by either hand or power seamers, both available on a job rental basis. The seaming process completely encloses and seals all clips and fasteners for the most watertight seal available. The US-200 panel, in addition to the standard 90-degree seam, can be double-locked to obtain a 180 degree architectural profile. The standing seam system is especially suitable where roof slopes are long and/or low, and unusually long panels are required. Available in various gauges of galvanized steel, galvalume, zincalume, aluminum, copper, zinc and stainless steel. Regardless of which material is selected, the optional stiffening ribs or striations are highly recommended in order to reduce the slight surface waviness of the metal known as “oil-canning.” Note: “oil-canning” is a natural phenomenon inherent in sheet metal products and therefore is not cause for rejection of the material.
US-200 Standing Seam Panel
The Ultra Seam standing seam system utilizes state of the art technology for roof integrity and positive weather-tightness. The Ultra Seam US-200 panel has been extensively tested in both steel and aluminum, and meets the stringent requirements of the “Standard Test Method for Structural Performance of SSMRS by Uniform Static Air Pressure Difference,” which has been adopted as ASTM E-1592. Seams require machine closing, by either hand or power seamers, both available on a job rental basis. The seaming process completely encloses and seals all clips and fasteners for the most watertight seal available. The US-200 panel, in addition to the standard 90-degree seam, can be double-locked to obtain a 180 degree architectural profile. The standing seam system is especially suitable where roof slopes are long and/or low, and unusually long panels are required. Available in various gauges of galvanized steel, galvalume, zincalume, aluminum, copper, zinc and stainless steel. Regardless of which material is selected, the optional stiffening ribs or striations are highly recommended in order to reduce the slight surface waviness of the metal known as “oil-canning.” Note: “oil-canning” is a natural phenomenon inherent in sheet metal products and therefore is not cause for rejection of the material.
Ultra Seam, Inc.
Ultra Seam standing seam metal roofing and siding products provide an ideal architectural solution for almost any type of structure. Ultra Seam products utilize state of the art continuous panel length technology to provide the perfect blend of function and aesthetics at competitive prices. With fifteen manufacturing facilities nationwide, Ultra Seam products are readily available to meet your demanding construction schedule.
Whether your requirements are for low or steep slope, mansard, retrofit, or equipment screens to hide rooftop clutter, Ultra Seam systems are suitable for either spanning across purlins on typical spacing, or laid directly over rigid insulation and/or solid decking. Many combinations of panel widths, rib heights and seam profiles provide extensive application and design flexibility.
Ultra Seam systems include panels, clips, fasteners, and flashing, custom designed to meet the needs of your particular project. Ultra Seam products are available in 22, 24 and 26 gauge galvanized steel, galvalume, zincalume, .032 or .040 aluminum, copper, zinc and stainless steel.
Visit Ultra Seam for metal roofing needs!
Whether your requirements are for low or steep slope, mansard, retrofit, or equipment screens to hide rooftop clutter, Ultra Seam systems are suitable for either spanning across purlins on typical spacing, or laid directly over rigid insulation and/or solid decking. Many combinations of panel widths, rib heights and seam profiles provide extensive application and design flexibility.
Ultra Seam systems include panels, clips, fasteners, and flashing, custom designed to meet the needs of your particular project. Ultra Seam products are available in 22, 24 and 26 gauge galvanized steel, galvalume, zincalume, .032 or .040 aluminum, copper, zinc and stainless steel.
Visit Ultra Seam for metal roofing needs!
Tuesday, April 3, 2007
MetalWorks Shingle Profiles and Physical Data
AstonWood and StoneCrest
Standard Shingles
:Painted Galvanized Steel
:Minimum Slope 4" in 12" (10.16 cm in 30>48cm)
:Shingle width overall: 39 3/4" (100.96cm)
:Shingle height overall: 12-5/8" (32.06cm)
:Shingle exposure area: 3.28 sq. ft. (0.30m2)
(39-3/8" x 12") (100.01 cm x 30.48cm)
:Shingles per box: 30 Panels
:Coverage per box: 98.4 sq.ft. (9.14m2)
(approx 1 square)
:Weight per shingle: 2.1 lbs (0.95kg)
:Weight per square: 64lbs (29.03kg)
:Material: Nominal 0.01" (0.03cm) thickness, including G90 galvanization and paint coatings. Exterior finish is fluoropolymer (PVDF) with anti-corrosive primer, 1
mil dry film thickness. Interior finish is a wash coat and anti-corrosive primer, 0.6 mil dry film thickness.
:Univeral Clip: 1-1/4" (3.17cm) wide x 2-1/8" ( 5.39cm)long x 0.20" (0.5 cm)deep
:Clip Material: 0.015" (0.03cm)thick, G90 galvanized steel.
STONECREST SLATE SHINGLES
:Painted Galvanized Steel
:Minimum slope: 4" in 12" (10.16cm in 30.48cm)
:Shingle width-overall: 39.3/4" (100.96cm)
:Shingle height overall: 12-5/8"(32.06cm)
:Shingle exposure area: 3.28sq.ft.(0.30m2) (39.3/8" x 12") (100.01cm x 30.48cm)
:Shingles per box : 30 panels
:Coverage per box: 98.4 sq.ft. (9.14 m2)
(approx 1 square)
:Weight per shingle: 2.5lbs (1.13kg)
:Weight per square: 5lbs (34.01 kg)
:Material:Nominal 0.01"(0.04cm)thickness, including G90 glavanization and paint coatings. Exterior finish is fluoropolymer(PVDF) with anti-corrosive primer, 1 mil dry film thickness. Interior finish is a wash coat with anti-corrosive primer, 0.6 mil dry film thickness.
:Univeral Clip: 1-1/4"(3.17cm)wide x 2-1/8" (5.39cm)long x 0.20"(0.5cm)deep
:Clip Material: 0.015:(0.03cm)thick, G90 Galvanized steel
ASHTONWOOD AND STONECREST
GALVALUME PLUS
:Bare Galvalume Plus
:Minimum slope: 4"in 12"(10.16cm in 30.48cm)
:Shingle with-overall: 39-3/4"(100.96cm)
:Shingle height-overall: 12-5/8"(32.06cm)
:Shingle exposure area: 3.28sq.ft. (0.30m2) (39-3/8" x 12") (100.01cm x 30.48cm)
:Shingles per box: 30 panels
:Coverage per box: 98.4 sq.ft. (9.14m2) Approx 1 square.
:Weight per shingle: 2.2lbs (0.99kg)
:Weight per square: 65lbs (29.48kg)
:Material: Nominal 0.01" (0.03cm)thickness
:Univeral clip: 1-1/4"(3.17cm)wide x 2-1/8"(5.39cm)long x 0.20"(0.5cm)deep
:Clip material: 0.015"(0.03cm)thick, G90 glavanized steel.
STONECREST COPPER SHINGLES
:Copper
:Minimum slope: 4"in12" (10.16cm in 30.48cm)
:Shingle width-overall: 39-3/4"(100.96cm)
:Shingle exposure area: 3.28 sc.ft. (0.30M2) (39-3/8" x 12")(100.01 cm x 30.48cm)
:Shingles per box: 15 panels
:Coverage per box: 49.25 sq.ft. (4.57m2) (Approx 1/2 square)
:Weight per shingle: 3.5lbs(1.59kg)
:Weight per square: 105lbs (47.75kg)
:Material: Nominal 0.026"(0.06604cm)thickness.
:Univeral Clip:1-1/4"(3.17cm)wide x 2-1/8"(5.39cm)long x 0.20" (0.5cm)deep
:Clip Material: 0.01"(0.04cm)thick, Stainless Steel.
Standard Shingles
:Painted Galvanized Steel
:Minimum Slope 4" in 12" (10.16 cm in 30>48cm)
:Shingle width overall: 39 3/4" (100.96cm)
:Shingle height overall: 12-5/8" (32.06cm)
:Shingle exposure area: 3.28 sq. ft. (0.30m2)
(39-3/8" x 12") (100.01 cm x 30.48cm)
:Shingles per box: 30 Panels
:Coverage per box: 98.4 sq.ft. (9.14m2)
(approx 1 square)
:Weight per shingle: 2.1 lbs (0.95kg)
:Weight per square: 64lbs (29.03kg)
:Material: Nominal 0.01" (0.03cm) thickness, including G90 galvanization and paint coatings. Exterior finish is fluoropolymer (PVDF) with anti-corrosive primer, 1
mil dry film thickness. Interior finish is a wash coat and anti-corrosive primer, 0.6 mil dry film thickness.
:Univeral Clip: 1-1/4" (3.17cm) wide x 2-1/8" ( 5.39cm)long x 0.20" (0.5 cm)deep
:Clip Material: 0.015" (0.03cm)thick, G90 galvanized steel.
STONECREST SLATE SHINGLES
:Painted Galvanized Steel
:Minimum slope: 4" in 12" (10.16cm in 30.48cm)
:Shingle width-overall: 39.3/4" (100.96cm)
:Shingle height overall: 12-5/8"(32.06cm)
:Shingle exposure area: 3.28sq.ft.(0.30m2) (39.3/8" x 12") (100.01cm x 30.48cm)
:Shingles per box : 30 panels
:Coverage per box: 98.4 sq.ft. (9.14 m2)
(approx 1 square)
:Weight per shingle: 2.5lbs (1.13kg)
:Weight per square: 5lbs (34.01 kg)
:Material:Nominal 0.01"(0.04cm)thickness, including G90 glavanization and paint coatings. Exterior finish is fluoropolymer(PVDF) with anti-corrosive primer, 1 mil dry film thickness. Interior finish is a wash coat with anti-corrosive primer, 0.6 mil dry film thickness.
:Univeral Clip: 1-1/4"(3.17cm)wide x 2-1/8" (5.39cm)long x 0.20"(0.5cm)deep
:Clip Material: 0.015:(0.03cm)thick, G90 Galvanized steel
ASHTONWOOD AND STONECREST
GALVALUME PLUS
:Bare Galvalume Plus
:Minimum slope: 4"in 12"(10.16cm in 30.48cm)
:Shingle with-overall: 39-3/4"(100.96cm)
:Shingle height-overall: 12-5/8"(32.06cm)
:Shingle exposure area: 3.28sq.ft. (0.30m2) (39-3/8" x 12") (100.01cm x 30.48cm)
:Shingles per box: 30 panels
:Coverage per box: 98.4 sq.ft. (9.14m2) Approx 1 square.
:Weight per shingle: 2.2lbs (0.99kg)
:Weight per square: 65lbs (29.48kg)
:Material: Nominal 0.01" (0.03cm)thickness
:Univeral clip: 1-1/4"(3.17cm)wide x 2-1/8"(5.39cm)long x 0.20"(0.5cm)deep
:Clip material: 0.015"(0.03cm)thick, G90 glavanized steel.
STONECREST COPPER SHINGLES
:Copper
:Minimum slope: 4"in12" (10.16cm in 30.48cm)
:Shingle width-overall: 39-3/4"(100.96cm)
:Shingle exposure area: 3.28 sc.ft. (0.30M2) (39-3/8" x 12")(100.01 cm x 30.48cm)
:Shingles per box: 15 panels
:Coverage per box: 49.25 sq.ft. (4.57m2) (Approx 1/2 square)
:Weight per shingle: 3.5lbs(1.59kg)
:Weight per square: 105lbs (47.75kg)
:Material: Nominal 0.026"(0.06604cm)thickness.
:Univeral Clip:1-1/4"(3.17cm)wide x 2-1/8"(5.39cm)long x 0.20" (0.5cm)deep
:Clip Material: 0.01"(0.04cm)thick, Stainless Steel.
Subscribe to:
Posts (Atom)